This is great. My guess it will keep working much longer.
But perhaps when you put it down for a while you will enter the same problem. Electro motors, there are lots of different principles, sometimes stop on a point, they can't start. If this happens every time, you switch it off, there is a malfunction. This time, perhaps only a little dust gave to much friction, to come on.
The induction motor, in your Blyss, could have one defective coil in its rotor, but the chance it will stop on the same place again, will be slim. If it becomes annoying, because you have to rotate it more often, the motor should be replaced. (or start saving for a new dehumidifier) Oct 06, 2014. Paperport 11 serial number.
. Wireless Alarm System BLY1 Barcode 283 Wireless Alarm System.indd 1 10:57.
BLY1 Wireless Alarm System Let’s get started. These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference.
Getting started. Introduction and Safety Overview of System Planning your Installation Installing your System. BLY1 Wireless Alarm System Getting Type box started. Introduction and Safety Overview of System Planning your Installation Installing your System 9-15 Wireless Alarm System.indd 3 10:57.
![Guide Guide](/uploads/1/2/4/0/124054276/137173803.jpg)
Introduction & Safety BLY1 Wireless Alarm System INTRODUCTION The wireless alarm system is designed to protect your home. It is a simple to use, easy to install unit. No special tools or training are required, all fixings are included. IMPORTANT: Please read this manual carefully, in full, before commencing installation.
Overview of System BLY1 Wireless Alarm System This wireless alarm system is based on wireless radio technology to give exceptional levels of protection and reliability. It has the ability to control up to eight detectors, three remote keys (optional accessory) and one wireless siren. Overview of System BLY1 Wireless Alarm System System features. Detector /Key /External Siren learning – Every wireless device (detector, Key, External Siren) contains an unique identification code. During installation, the control unit will learn which devices belong within your system by receiving coded radio transmissions from each detector. Planning your Installation BLY1 Wireless Alarm System Location of components Control unit – Location In choosing a suitable location you should bear in mind:. The need to reach the control unit easily, within the 30 seconds, when entering and leaving the premises, ideally passing only one detector.
Ge Dehumidifier User Manual
Planning your Installation BLY1 Wireless Alarm System Planning the location of system components Example of a domestic layout The 2 sample layouts below are intended as guides only but demonstrate two examples of how a house can be protected with the system. Planning your Installation BLY1 Wireless Alarm System The PIRs have been separately placed in bedroom 1, bedroom 2, bedroom 3, and the area where the control panel is installed, to protect these areas. The Door/Window contact detectors have been positioned to protect the front door, back door and windows on the 1st floor.
Installing your System BLY1 Wireless Alarm System Installing the Control unit. Remove and retain the two holding screws from front cover of ST3x25KA control unit and screw carefully hinge off the front cover. Hole depth ˃22mm Fitting 56mm protrude surface. Installing your System BLY1 Wireless Alarm System Power up the Wireless Devices and learning to the CU Before powering up the devices please read through this information regarding batteries: 1. An adult must carry out battery replacement and installation. Remove exhausted batteries from this product. Installing your System BLY1 Wireless Alarm System Powering up the Wireless PIR Detector(s): 1.
Remove battery cover and insert two LR03 “AAA” size alkaline batteries incorrect polarity as shown. Replace battery compartment cover. AAA 1.5V AAA 1.5V When the PIR is first powered up it will take 2 minutes for it to warm-up before it can be linked to the control unit. Installing your System BLY1 Wireless Alarm System 2.2 a PIR Detector, trigger the PIR detector by simply moving your hand in front of the detector. Learn PIR When a PIR Detector has been learnt successfully, Z5, Z6, Z7 or Z8 zone LED depending on which next zone is unprogrammed) will flash.
Installing your System BLY1 Wireless Alarm System 3. Trigger the next device within 10 seconds to learn it and repeat for additional devices. If the system has reached its maximum capacity and no more devices ca be added. The control unit will not beep any more. Installing your System BLY1 Wireless Alarm System 4.
Locate the detector on the back plate and replace the retaining screw at the base of the unit. Align the magnet as described above and fix in position with the two screws provided. Installing your System BLY1 Wireless Alarm System Movement Detector/PIR final setup IMPORTANT: To extend the battery life, wireless PIR detectors are designed to detect once only before entering a “Sleep” condition for two minutes during which the unit will not trigger. Any movement seen by the PIR during this period would cause “Sleep”.
![Sony user manual Sony user manual](/uploads/1/2/4/0/124054276/203556415.jpg)
Instruction Manual
BLY1 Wireless Alarm System Getting more started. Using the System 17-19 Maintenance Extending the System Specifications 20-21 Troubleshooting Guide Disposal and Recycling Wireless Alarm System.indd 17 10:57. Using the System BLY1 Wireless Alarm System Control unit When the control unit is powered up, it will remain in standby mode. The PIN code can also disarm the system and put it into standby mode. A) Changing the user PIN code The User PIN code is factory set to 1234. Using the System BLY1 Wireless Alarm System g) Part Arm the alarm system while at home Press “Part-Arm” button at the control unit or press “PARTIAL ARM” button at the remote key, (optional accessory) close the door and leave the house within the exit delay time (30 seconds at factory setting,) both PIR and magnetic contact are activated for protection after the exit delay time elapsed.
Using the System/ BLY1 Wireless Alarm System Maintenance/ Extending the System Default settings Parameter Ex-factory Value User PIN code 1234 Entry/Exit delay 30 seconds Siren Duration 3 minutes Zone allocation for PIR and MC Detectors Zone 1 to 4 Magnetic Contact. Specifications BLY1 Wireless Alarm System Control unit Type Microprocessor based wireless control unit Housing material Zones 8 Alarm Zones–1 detector maximum per zone (8 detectors capacity) Entry/Exit Delay 30 seconds Siren Duration 3 minutes RF Receiver Frequency: 433MHz Power Supply 15V 500mA 50Hz AC/AC mains adaptor and 1 x 9V DC PP3 Alkaline for back-up power. Specifications/ BLY1 Wireless Alarm System Troubleshooting Control Panel Power Supply Adaptor Type AC/AC Adaptor with 3-pin UK style Housing material Rated Supply 230VAC 50HZ supply Output Extra Low Voltage (AC15V max at 500mA AC) Troubleshooting 1) Control unit (CU) Symptoms Possible causes and cures No power supply to unit.
Check with your local authority or retailer for recycling advice. Declaration B&Q hereby declares that this wireless product BLY1 is in compliance with the essential requirements and other relevant provisions of the Radio and Telecommunications Terminal Equipment (R&TTE) directive, 1995/5/EC. BLY1 Wireless Alarm System Appendix Appendix LED Alarm Indication Zone - Location Table Wireless Alarm System.indd 24 10:57. Appendix B BLY1 Wireless Alarm System LED Alarm Indication: Power Tamper Z1/Z5 Z2/Z6 Z3/Z7 Z4/Z8 (GREEN) (RED) (RED) (RED) (RED) (RED) STATUS Power Ready AC Failure Low Battery Flashing Z1 Alarm Z2 Alarm Z3 Alarm Z4 Alarm Z5 Alarm Flashing. BLY1 Wireless Alarm System Zone - Location Table: Zone Number Location B&Q, Chandlers Ford, Hants, SO53 3LE United Kingdom EAN 283 www.diy.com Customer Helpline 0844 736 9169 BLY1 Wireless Alarm System - Version 01 Wireless Alarm System.indd 26 10:57.
Typical price £219.00 The Blyss Excellence 28L dehumidifier has a large 28-litre claimed-extraction capacity, which makes it sound ideal for large rooms where you have problems with damp or condensation. We put all our dehumidifiers to the test - running them at both 10°C and 21°C to see how well they do at pulling moisture from the air in different environments. Read our Blyss Excellence review to find out how this Blyss dehumidifier did when we put it through its paces in our rigorous lab tests. Serial number program bengkel 2.0.